SAL Premier S9076TC LED Downlight 30/40W 240mm IP64 - White

Description

Dual-power downlight. High output. No dimmer needed.

The SAL Premier S9076TC/WH/DP is a non-dimmable, dual-power 30W/40W recessed LED downlight with selectable colour temperature (3000K / 4000K / 5700K), a premium white powder-coated aluminium body, recessed opal polycarbonate diffuser, CA-90 insulation contact rating, and IP64 moisture resistance — designed for residential, retail, and commercial interior ceiling applications with a 240mm cut-out. With a pre-wired flex and plug remote LED driver featuring flickerCONTROL technology, up to 4200 lm at 4000K (40W), a 90° wide beam, and a clean 280mm diameter profile, the S9076TC/WH/DP is a high-output dual-power downlight suited to large rooms, open-plan living areas, retail spaces, and commercial interiors where maximum lumen output at a single point is required without a full dimming system.

• Power: 30W or 40W (selectable dual-power driver)
• Lumens at 40W: 3500 lm (3000K) / 4200 lm (4000K) / 3800 lm (5700K)
• CCT: Selectable 3000K / 4000K / 5700K
• CRI: 80
• Beam Angle: 90°
• IP Rating: IP64
• Insulation Rating: CA-90 (IC-4 equivalent)
• Dimmable: No (DP = Dual Power non-dimmable variant)
• Body: Premium aluminium, white powder coat
• Diffuser: Recessed opal polycarbonate
• Cut-out: 240mm | Width: 280mm | Height: 96mm
• Driver: Remote, non-dimmable, dual-power with flickerCONTROL, flex and plug
• Lamp life: 51,000 hrs (L70)
• Operating temp: 0 to 40°C
• IPART approved

Important: Non-dimmable — do not connect to a wall dimmer. Set power level (30W/40W) and CCT before installation with power OFF. Installation by a licensed electrician is required in accordance with AS/NZS 3000.

Fast shipping across Australia — order online now for quick dispatch.

DP = Dual Power — Output Flexibility Without a Dimmer

The S9076TC/WH/DP's built-in driver lets the installer select either 30W (economy mode) or 40W (full output) at the time of installation. This is a switched power selection, not continuous dimming — the DP driver does not support wall dimmer connection. At full 40W output, the fitting delivers up to 4200 lm at 4000K across a 90° wide beam — enough to serve as the primary downlight in a large living room, retail space, or open-plan commercial interior from a single fitting point. Economy 30W mode reduces running cost while maintaining the same beam distribution. For a dimmable version, see the S9076TC/WH/HP sibling, which offers optional dimming via trailing edge, 1-10V, or DALI/DSI control.

IP64 and CA-90 rated — wet zones and insulated ceilings covered.

The IP64 rating means the fitting is fully dust-tight and protected against water splashes from any direction — suitable for bathroom zones (Zone 2 and general areas), laundries, and other damp interior locations, subject to local wiring regulations and AS/NZS 3000 zone requirements. The CA-90 insulation contact rating means the downlight body can be covered by standard thermal insulation batts in residential ceilings without creating a fire risk — eliminating the need for insulation management around the fitting. Always refer to the SAL installation instructions for insulation coverage limits and zone compliance requirements.

Selectable CCT — three colour temperatures, one fitting.

A switch on the driver selects the colour temperature before installation with power off: 3000K Warm White for residential living areas, dining rooms, hospitality, and retail where a warm, welcoming ambience is preferred; 4000K Cool White for kitchens, bathrooms, offices, and commercial spaces where neutral, crisp white light is preferred; and 5700K Natural Daylight for commercial offices and retail spaces where maximum visual clarity is required. The flickerCONTROL driver technology reduces light flicker to levels below the thresholds associated with headaches and photosensitive conditions — important for office and retail environments where occupants spend extended periods under artificial lighting.

Q: What is the difference between the DP and HP variants?
A: Both are the SAL Premier S9076TC 240mm recessed LED downlight with the same body, cut-out, diameter, beam, and selectable CCT. The DP (this product) has a dual-power non-dimmable driver (30W or 40W selectable at installation). The HP variant offers optional dimming via trailing edge, 1-10V, or DALI/DSI control. Choose DP for non-dimming installations; choose HP where dimming control is required.

Q: Is this fitting suitable for bathrooms?
A: Yes — IP64 provides full dust protection and water splash protection from any direction, meeting the IP requirements for Zone 2 and general areas in Australian bathrooms under AS/NZS 3000. Confirm the specific zone requirements with your electrician prior to installation.

Q: Can I cover this fitting with ceiling insulation?
A: Yes — the CA-90 insulation contact rating means the fitting can be covered by standard thermal insulation batts in residential ceilings. Refer to the SAL installation instructions for the specific insulation coverage depth and type permitted. Always follow the installation instructions to maintain the CA-90 rating.