SAL LT Series LT4014TC LED Tubular Lamp 14W E27 Tri-CCT - Dimmable

Description

14W dimmable. Three colours. Direct CFL replacement for E27 fittings.

The SAL LT4014TC/E27D is a 14W dimmable LED tubular lamp with selectable colour temperature (3000K / 4000K / 6000K), an E27 Edison Screw base, opal polycarbonate diffuser over a poly-covered aluminium body, and a 200° wide beam angle — designed as a direct LED replacement for traditional CFL and incandescent globes in table lamps, pendant fittings, ceiling rose holders, chandeliers, and decorative lamp fittings across Australian residential and commercial interiors. An integral trailing-edge dimmable LED driver delivers up to 1750 lm at 4000K from a compact 42mm x 133mm tubular form factor.

• Power: 14W, 240V AC, 50Hz
• Lumens: 1400 lm (3000K) / 1750 lm (4000K) / 1700 lm (6000K)
• CCT: Selectable 3000K / 4000K / 6000K via base selector switch
• CRI: >80
• Beam Angle: 200°
• Base: E27 Edison Screw (27mm)
• Dimmable: Yes — Trailing Edge
• Body: Opal polycarbonate diffuser, poly-covered aluminium
• Diameter: 42mm | Length: 133mm
• IP Rating: IP20 (interior dry-location use only)
• Operating Temp: 0 to 25°C
• Pack Size: Available in packs of 10

Important: Always switch power OFF before adjusting the CCT selector switch — equipment damage may occur if switched while live. Use only with trailing-edge LED-rated wall dimmers.

Fast shipping across Australia — order online now for quick dispatch.

14W of Dimmable, Tri-CCT Output in a CFL-Sized Tube

The LT4014TC/E27D fills a gap that many LED lamps don't address: a high-lumen, dimmable, selectable-CCT lamp in the tubular CFL form factor that Australian table lamps, pendants, and ceiling rose fittings were designed around. At 14W delivering up to 1750 lm at 4000K, it replaces a typical 60–75W incandescent or 15–18W CFL with roughly 80% energy saving over incandescent equivalents. The 200° near-omnidirectional beam distributes light in all directions — unlike directional GU10 or PAR lamps — making it well suited to shaded table lamp fittings and open pendant holders where the shade diffuses light all around the fitting.

Three colour temperatures — choose before fitting, with power off.

A selector switch on the base sets the CCT: 3000K Warm White — a golden, warm tone matching traditional incandescent lamps, preferred for residential living areas, dining rooms, bedrooms, and hospitality interiors; 4000K Cool White — a neutral, crisp white suited to kitchens, studies, offices, and retail environments; and 6000K Daylight — a cool, bright output suited to task lighting and applications where maximum visual acuity is required. Always switch the mains supply OFF before adjusting the CCT selector — equipment damage may occur if switched while live.

Trailing-edge dimmable — smooth performance with modern Australian dimmers.

The integral trailing-edge dimmable driver is compatible with most modern Australian LED-rated trailing-edge wall dimmers, including Clipsal Iconic Dimmable, HPM, Mercator, and Legrand. Dimming is available across all three selectable CCTs. Always confirm your dimmer is a trailing-edge LED-rated type — leading-edge (incandescent/halogen) dimmers may cause flicker or reduced dimming range. Check the dimmer's minimum LED load rating, particularly when running a small number of 14W lamps on a single dimmer circuit.

Q: What is the difference between the E27D and B22D variants?
A: Both are SAL LT4014TC/D 14W dimmable selectable-CCT tubular lamps with identical light output, CRI, beam angle, and 42 x 133mm dimensions. The LT4014TC/E27D (this product) has an E27 Edison Screw base — the large screw fitting used in most Australian table lamps, pendant holders, and ceiling rose lamp holders. The LT4014TC/B22D sibling has a B22 bayonet cap base — the traditional push-and-twist Australian bayonet fitting. Choose based on the lamp holder type in your fitting.

Q: Will this lamp dim smoothly?
A: Yes, when used with a compatible trailing-edge LED-rated wall dimmer. Use modern Australian trailing-edge dimmer models (Clipsal Iconic Dimmable, HPM, Mercator, Legrand). Leading-edge dimmers may cause flicker or reduced minimum dim level. Check the dimmer's minimum LED load rating, as a single 14W lamp may fall below some dimmers' minimum load threshold.

Q: Can I change the CCT after installation?
A: Yes — the CCT selector switch is on the base of the lamp. Switch the mains supply OFF, adjust the CCT selector, then restore supply. Never adjust the CCT switch while the lamp is live, as equipment damage may occur.